995 REVERSIBLE PLOW
Reversible Plow
- Moldboard frame pivots with the bottoms
- Plastic moldboard and steel shins
- Landsides with wedges
- Front gauge wheels
Features
995 mainframeThe V-style mainframe of the 995 Moldboard Plow distributes weight for good penetration.
The mainframe is made of high-strength 178-mm x 102-mm (7-in. x 4-in.) tubing that is 8-mm (5/16-in.) thick to handle the stress of high-horsepower tractors working in tough ground conditions.
Moldboard frameAll 995 Moldboard Plows use only one set of bottoms.
The moldboards are reversed laterally by a hydraulic cylinder that is standard equipment. There are several advantages of this design over traditional two-way roll-over plows with two sets of bottoms:
- Requires less 3-point hitch capacity
- Requires less ballasting of the tractor front end
- Eliminates initial cost and service requirements for one complete set of standards and bottoms
Integral on-land hitch 
The integral hitch gives unexcelled maneuverability in turns and when parking in tight areas:
- Category 3/3N Quik-Coupler compatible
- Tractor rockshaft lever controls the raising and lowering of the plow
- Maximum plowing depth to 356 mm (14 in.)
- Provides ample clearance between the tractor tires and the plow
Front gauge wheelsThe front gauge wheels can be adjusted to limit the plowing depth to 356 mm (14 in.). They come equipped with 6.70-15 tires.
995 Moldboard Plow rear gauge wheelsTwo front and one rear gauge wheels are standard equipment on the 995 Moldboard Plow:
- Equipped with 6.70-15 tires for good flotation
- Easy turnbuckle adjustment on rear gauge wheel
- Adjustable front gauge wheels limit the plowing depth to 356 mm (14 in.)
Specifications
Compare the specifications of up to 4 models
| Key Specs | 995-reversible-plow Current Model |
|---|---|
| Total width of cut | |
| Option 1 | 2.3 m 7.5 ft |
| Option 2 | 2.7 m 9 ft |
| Option 3 | 3.2 m 10.5 ft |
| Option 4 | 3.7 m 12 ft |
| Plowing depth | 35.6 cm 14 in. |
| Horsepower required - Option 1 | 5-bottom: 96.9-123 kW 130-165 hp |
| Option 2 | 6-bottom: 111.9-130.5 kW 150-175 hp |
| Option 3 | 7-bottom: 130.5-149.1 kW 175-200 hp |
| Option 4 | 8-bottom: 149.1-186.4 kW 200-250 hp |
| Hitch | |
| Type | Category 3N or 3 |
| Steering | Integral, in-furrow No Integral, on-land Yes Semi-integral, on-land No Drawn, in-furrow No Drawn, on-land No Quick-coupler compatible Yes |
| Reversible | Type of reversing Hydraulic cylinder Yes |
| No. of bottoms | |
| Option 1 | 5 |
| Option 2 | 6 |
| Option 3 | 7 |
| Option 4 | 8 |
| Option 5 | |
| Option 6 | |
| Option 7 | |
| Option 8 | |
| Total width of cut | |
| Adjustment | |
| Option 1 | 2.3 m 7.5 ft |
| Option 2 | 2.7 m 9 ft |
| Option 3 | 3.2 m 10.5 ft |
| Option 4 | 3.7 m 12 ft |
| Option 5 | |
| Option 6 | |
| Option 7 | |
| Option 8 | |
| Weight (approximate) | |
| Option 1 | 1,678 kg 3,700 lb |
| Option 2 | 1,860 kg 4,100 lb |
| Option 3 | 2,041 kg 4,500 lb |
| Option 4 | 2,440 kg 5,368 lb |
| Option 5 | |
| Option 6 | |
| Option 7 | |
| Option 8 | |
| Clearances | |
| Vertical | 81.3 cm 32 in. |
| Fore-aft | |
| Standards | |
| Shearbolt | Standard |
| Safety trip | Optional |
| Spring reset | No |
| Hydraulic | No |
| Coulters | |
| Option 1 | |
| Option 2 | |
| Option 3 | |
| Bottoms | |
| Option 1 | Plowing depth 35.6 cm 14 in. Steel moldboard |
| Option 2 | Plastic moldboard |
| Option 3 | |
| Option 4 | |
| Option 5 | |
| Option 6 | |
| Frame | |
| Option 1 | Thickness: 17.8x10.2x0.8 cm 7x4x0.313 in. |
| Option 2 | |
| Option 3 | |
| Expandable | |
| Horsepower required | |
| Option 1 | 5-bottom: 96.9-123 kW 130-165 hp |
| Option 2 | 6-bottom: 111.9-130.5 kW 150-175 hp |
| Option 3 | 7-bottom: 130.5-149.1 kW 175-200 hp |
| Option 4 | 8-bottom: 149.1-186.4 kW 200-250 hp |
| Landing | |
| Type | |
| Gauge wheel | |
| Type | |
| Tires | |
| Type | |
| Trashboards | |
| Type | |
| Additional features | |
| Options |
Accessories and Attachments
Bottoms
Steel shinsSteel shins are available as a field-installed option only.
The frog is pre-drilled at the factory to accept this attachment.
With this attachment, the steel shins will allow longer wear life when soil first comes into contact with the plow, but still offers the option of a plastic moldboard for sticky soil conditions.
Hydraulics
Lighting
SMV Security Emblem - BP16365
Warning Lights - BP16298
Miscellaneous
Double landsidesDouble landsides allow converting five- and six-bottom plows equipped with wedges for operation in hard ground conditions.
The bundle includes one extra set of landsides for the front bottoms, four regular large landsides for the rear bottom, and all necessary attaching hardware.
Double landsidesDouble landsides allow converting five- and six-bottom plows equipped with wedges for operation in hard ground conditions.
The bundle includes one extra set of landsides for the front bottoms, four regular large landsides for the rear bottom, and all necessary attaching hardware.
Landsides with wedgesThis bundle is for five- or six-bottom plows. It allows converting five- or six-bottom plows equipped with double landsides for operation in average-to-soft soil conditions.
The bundle includes a set of wedges for all bottoms, one set of extra-large landsides for the rear bottom, and all the necessary attaching hardware.
NOTE: Due to line-of-draft characteristics, the seven- and eight-bottom plows do not require use of wedges.
Landsides with wedgesThis bundle is for five- or six-bottom plows. It allows converting five- or six-bottom plows equipped with double landsides for operation in average-to-soft soil conditions.
The bundle includes a set of wedges for all bottoms, one set of extra-large landsides for the rear bottom, and all the necessary attaching hardware.
NOTE: Due to line-of-draft characteristics, the seven- and eight-bottom plows do not require use of wedges.
Front gauge wheelFront gauge wheels can be added to control the plowing depth.
- Can be adjusted to limit the plowing depth to 356 mm (14 in.)
- Equipped with 6.70-15 tires