Need 24/7 Parts? Call 855-573-7278

FIND YOUR JAMES RIVER

1910 AIR COMMODITY CART

Tow-Behind Air Commodity Cart

Choice of auger or conveyor
Stationary single-shoot manifold
In-line drive system transfers power efficiently
New 550-bushel grain tank capacity on tow-behind models

Features

Choice of auger or conveyor

254-mm (10-in.) auger on 15,200-L (430-bu) cart

As growers look for ways to increase efficiencies, one solution is to shorten the time required to fill. By increasing pit stop productivity, growers are able to cover more ground per day.

Producers have the choice of an auger or conveyor to fit their needs.

The 254-mm (10-in.) auger:

Available on the 12,300-L (350-bu), 15,200-L (430-bu), and 19,400-L (550-bu) carts
Loading rate 1800-L (50-bu) per minute
Balanced for safe, convenient movement between storage and filling positions
Able to fit under the meters for tank cleanout

The 203-mm (8-in.) auger:

Available on 8,800-L (250-bu), 9,500-L (270-bu), and 12,000-L (340-bu) carts
700-L (20-bu) per minute fill rate

305-mm (12-in.) conveyor

The 305-mm (12-in.) conveyor provides producers with a gentle conveyance system:

305-mm (12-in.) wide belt with risers spaced on 150-mm (6-in.)
1400-L (40-bu) per minute fill rate
Can also transfer fertilizer
Cleanout trap door at the bottom
Optional on all 1910 carts

The telescoping spout provides the following benefits:

Decreases fill time
Easily fills each tank to the very top
Improves movement when going from one tank to another, matching the tank height

The metering system provides accuracy and convenience

A meter cartridge at each tank effectively meters seed or fertilizer into the primary manifold. Air carries the material to the secondary distributor for delivery to the openers on the seeding tool.

Meters are contained in a cartridge for convenient removal and are color coded for easy identification.

Metering system

A manual half-width disconnect is incorporated into the 1910 meter system:

Allows one-half of the metering system to be manually shut off for irregular shaped headlands, point rows, etc. on mechanical drive carts.
Allows the meter cartridge to be removed with material still in the tank(s).
Allows tanks to be emptied with meter and primary manifold in place.

Electric actuator on the C850 Air Cart

On the C850 Air Cart an electric actuator controls product flow from the tank to the meter housing:

Allows complete shut off of product flow with little effort
Allows the meter cartridge to be removed with material still in the tank(s).
Allows tanks to be emptied with meter and primary manifold in place.

Stairway and platform offer convenience and easy access

The easy-to-navigate staircase and large platform provide easy access to tank lids.

On tow-between carts, there is convenient front access to the platform, with step-over access when going from side-to-side over the front hitch.

Tow-between cart, front access

Tow-behind cart, rear access

Efficient air system ensures consistent product delivery

Secondary manifolds

Secondary manifold on seeding tool

One-piece removable lid with tether

Secondary manifolds with 25-mm (1-in.) diameter lines evenly distribute the seed and/or fertilizer from the primary manifold(s) to the furrow openers.

Primary hoses are color coded to conveniently connect the air distribution kit from the 1910 Cart to the seeding tool.

The 25-mm (1-in.) secondary lines used for seed are clear with a black spiral. For double-shoot air kits, hoses are clear with a green spiral.

The secondary manifold is made of durable, maintenance-free ethylene-propylene molded (EPDM) rubber. Features of the secondary manifold:

Rust resistant, important when applying fertilizer or treated seed
No tools required to remove lid
No long bolt in the secondary tower
Lid is tethered to the manifold
The outlet ports are numbered
Primary hoses are color coded to conveniently connect

Primary manifolds

Stationary double-shoot primary manifold

Primary manifolds are mounted below the tanks with 63.5-mm (2-1/2-in.) diameter tubes to distribute seed/fertilizer evenly to the secondary manifolds, which are located on the seeding tool.

63.5-mm (2-1/2-in.) primary lines are clear with either a black or green spiral:

Black spiral for single-shoot systems
Black and green spiral for double-shoot systems

Stationary single-shoot or stationary double-shoot primary manifolds are available.

Single-shoot air systems are used when seeding only or when applying a starter fertilizer along with the seed. Double-shoot air systems are used when applying higher levels of fertilizer, allowing simultaneous application of seed and fertilizer by placing them in two different locations in the seed row. With the proper 1910 Cart configuration, starter fertilizer can also be applied with the seed in a double-shoot air system.

High-output, hydraulically driven fan

Fan as seen on 19,400-L (550-bu) cart

The 1910 Commodity Air Cart uses an airstream to gently deliver seed and/or fertilizer to the openers. A strong, consistent airstream is necessary to keep product moving without plugging the air runs, while making sure damage is not occurring to the seed.

The large 450-mm (17.6-in.) diameter fan generates a low-velocity, high-volume airstream that carries the product to the openers. By using a high volume of air, there is less chance of damaging seed, while decreasing the likelihood of plugging the air system.

The fan is driven by the tractor's hydraulic system. It requires approximately 53- to 75-L/min (14 to 26-gpm) oil flow for operation.

IMPORTANT: The 53- to 75-L/min (14- to 26-gpm) is for the 1910 Cart fan only; additional hydraulic capacity from the tractor is also required for the hydraulic drive motors and for the seeding tool, depending on what seeding tool is chosen.

NOTE: Requires motor seal drain kit.

Hydraulic drives provide accurate metering and variable rate

Hydraulic drives

Starting in model year 2014, hydraulic drives became standard equipment on the 1910 air carts, offering consistent drive power to the meters. Hydraulic drives come standard with variable-rate drive and hydraulic calibration.

The drive system reduces a large number of mechanical and electrical components including transmissions, clutches, chain drives, sprockets, gears, and shafts by replacing them with a hydraulic drive motor, electrohydraulic valve, and a chain drive connecting the motor and meter.

Each meter has its own hydraulic drive motor and can be set independently of each other. It is recommended to use power beyond or another selective control valve (SCV) if power beyond is not available. Hydraulically powered meters minimize the pulsing effect found in chain driven systems. The motor speed is controlled by an electrohydraulic valve mounted on the motor.

Operators can shut off any meter from the in-cab display. The cart software comes with six pre-loaded rates for seeding. Map based prescriptions can be used with variable rates.

The system uses wheel speed from the cart to determine ground speed. If the cart wheel speed drops below 3.2 km/h (2 mph), the system will use tractor speed, if available, to maintain proper application rates when turning or coming out of a headland turn.

Hydraulic drive motor

Variable rate

Starting in model year 2014, hydraulic variable-rate drive became standard equipment for 1910 air carts. Quick changing rates are important for maintaining accuracy with variable-rate prescription applications.

Meter drive system

Meter drive system with safety shield installed

Hydraulic calibration

Hydraulic calibration makes it convenient to rotate the cart meters to perform accurate calibration.

More than one meter can be calibrated at a time. Following the below instructions for 1910 air carts:

Weigh bag, tare scale
Add bag to bottom of meter
Rotate the meters twice to charge them with product
Turn the meters until they stop
Weigh the bag with product inside
Enter the weight of the product on the in-cab display

Calibration tools and equipment

Operator performing calibration

Meter verification

Operators can perform meter verification without driving. In the meter verification page on the in-cab display, select the meter(s) to verify and the stationary checkbox. When the operator engages the calibration switch, the meter will turn the number of revolutions to meter out the amount of product for the area selected.

NOTE: It is highly recommended to have power beyond and load sense installed on the tractor hydraulic system to power the hydraulic drives. This feature will save fuel, as well as reduce hydraulic heat, while providing maximum performance by the tractor hydraulic system to the cart hydraulic drive motors. By having load sense, the tractor is only required to provide the pressure and flow that the drives require. Power beyond and load sense capability have been tested and approved for all 8x00, 9x00, and newer John Deere tractors. Older John Deere tractors and competitive tractors have not been tested for functionality. If power beyond is not available, an additional SCV will be needed to power hydraulic drives. See link for more information on power beyond kits.

NOTE: Hydraulic drives cannot be performance upgraded onto mechanical drive carts.

NOTE: For high application rates, it is recommended to utilize tractors with the hi-flow hydraulic pump option. See 1910 Commodity Cart tractor compatibility and requirements for more information.

SectionCommand™ system saves seed and fertilizer input costs

SectionCommand controls seed and fertilizer overlaps and skips

Controlling input costs and improving productivity are key producer requirements today. SectionCommand is an effective, integrated John Deere solution designed to meet these intensifying needs. SectionCommand manages both seed and fertilizer application by minimizing overlaps and skips while seeding with the John Deere 1910 and C850 Air Carts.

Owner benefits include:

Improved consistency of crop maturity at harvest
Improved consistency during emergence and growing season
Reduced seed input cost
Reduced fertilizer input cost
Increased time between fills due to input savings

SectionCommand is base equipment with optional deduct on all John Deere 1910 and C850 Air Carts. Each tank and meter will receive SectionCommand components. A two-tank cart will control sections out of both tanks, a three-tank cart will control sections out of all three tanks, and the C850 cart will control sections out of all four tanks. SectionCommand is also available as an attachment for field conversion (AFC) for all 1910 hydraulic drive carts. See AFC kit story for more information.

SectionCommand controls seed and fertilizer output by closing and opening gates on the bottom side of the meter. When the gates are open, commodity is metered out, and when closed, commodity stays and continues to rotate within the meter. The meter stays full at all times so immediately when the gate opens, the commodity can flow into the primaries and out to the tool. Since each meter section has its own gate, application rates and row-to-row accuracy are not compromised. The gates are utilized to control commodity output on all sections. Once the last gate needs closed, the entire meter will stop turning, stopping product flow.

Seeded fields photo

When commanded, electric over-hydraulic solenoids engage actuators to instantaneously close the gate for the needed section. The actuators are powered via hydraulics from the same circuit as the hydraulic drive motors. When power is cut, oil is diverted to retract the actuators and open the gates. The retraction is both powered and spring assisted, so it will always default to the seeding position. The oil from SectionCommand drains back through the fan motor case drain line and is coupled with an accumulator on the valve block to provide extra drainage capacity.

SectionCommand components as seen on back side of meter

SectionCommand components as seen on front side of meter

SectionCommand incorporates gate detection, which gives producers the satisfaction of knowing the gates are in position as commanded. Magnets on the back side of the gates are used in close proximity to the gate detection sensors to determine if the gates are open or closed. Should a gate not be in the commanded position, an alarm will alert the operator of the gate(s) in question. The blockage warning system works in conjunction with SectionCommand to give further confidence whether a given section is seeding or not when commanded.

SectionCommand meter cartridge showing one gate closed and magnet on backside of gate

Gate detection sensor

For maximum performance, SectionCommand should be controlled through John Deere Section Control. Coupling SectionCommand with John Deere Section Control provides the ultimate in precision seeding and productivity. If a Section Control activation is held by the producer, that same activation can be utilized for SectionCommand.

SectionCommand introduces the orange roller, which has the same number of flutes and spacing as the blue roller, but shorter flutes. It is for use only with SectionCommand when seeding seeds larger than 6 mm (0.25 in.) in diameter (soybeans, chick peas, etc.). The orange roller is not for use with cereal grains or fertilizer.

Orange roller, for use only with large seeds and SectionCommand

SectionCommand equalizer

Due to the varying lengths of product delivery hose used across the drill, SectionCommand has a built in equalizer feature to ensure consistent product delivery across the width of the drill when entering and exiting headlands. The software allows the producer to set the on/off product delivery times separately for the outermost opener and the innermost opener on the drill. Product delivery times are inputted for each tank on the cart, and the software creates a time delay for actuation of the gates.

Please see the Using SectionCommand video for more information.

Enabling SectionCommand equalizer

Input on/off times for outer opener versus inner opener on each tank

NOTE: Please reference CCMS solution 111434 for more information.

Wirelessly controlled hydraulic conveyance reduces operator physical effort

Operators continually seek easier and faster operations while seeding and reduce time spent filling and unloading.

Conveyance on 12,334-L (350-bu), 15,200-L (430-bu), and 19,400 (550-bu) carts is controlled by hydraulic cylinders on the conveyance arms. The cylinders move the main arm, swing arm, and elevation. Now operators can easily deploy the conveyance system with less effort.

Input to the system is received from one of two remotes. Each operator receives a wireless remote that can be operated from anywhere near the cart and a tethered remote that can be operated from ground level near the front meter. Each remote controls the same functions and gives flexibility of system control should two operators be in the area during cart fill and unload.

The remotes can start, stop, and control speed of the conveyance system. For added security, the speed control arm is retained on the conveyance and can override the remotes to slow down or stop the belt or auger.

Securing the auger or conveyor is now easier and gives the operator a greater sense of security with over-center latches on both the top and bottom of the conveyance.

Both the main and swing arms are longer giving operators greater flexibility in tendering vehicle parking locations.

Wireless remote

Receiver and tethered remote

A - Remote on/off

B - Conveyance stop/start

C - Conveyance slow down/speed up

D - Tilt/elevation

E - Main arm retract/extend

F - Swing arm retract/extend

Factory-installed hopper

Left-hand side of cart in transport

Left-hand side of cart in fill position

Left-hand side of cart in unload position

Low-profile hopper folder and unfolded

Low-profile hopper

For operators who fill carts from semi hopper bottoms or who desire full width meter clean out, John Deere has partnered with KSi® Conveyors to provide a low-profile hopper. The hoppers are compatible with all hydraulic conveyance carts. The hoppers utilize conveyor belts and are available for both the 254-mm (10-in.) auger and 305-mm (12-in.) conveyor. The hoppers are longer than competitive offerings on similar cart sizes.

The hoppers easily fold over to keep mud and rocks from being slung into the hopper and for tight maneuverability during transport and seeding. During fill and unload, flip the hoppers back over to move product.

Each hopper comes with both a large and small screen for optimizing product flow and catching foreign material during fills. Rubber skirting around the hopper provides flexibility during use and adds capacity to the hopper.

Please contact KSi Conveyors for ordering information.

KSi Conveyors Inc.
c/o Bruce Frank
1(888) 574-3277
+1(815) 457-2403
[email protected]
https://www.ksiconveyors.com/jddealer

KSi is a trademark of KSi Conveyor, Inc.

SectionCommand™ system field conversion kit

SectionCommand is available as an attachment for field conversion (AFC) for all hydraulic drive carts. See SectionCommand saves seed and fertilizer input costs for more information on benefits and workings of the system.

SectionCommand components on 1910 Cart with meter cartridge removed

SectionCommand on 1910 Air Cart

There are four main components needed to add SectionCommand onto 1910 hydraulic drive air carts:

1. SectionCommand AFC kit (listed in the table below, order one kit per meter), kit includes:

SectionCommand valve block and meter housing components
Gate detection controller
Electronic power module (EPM)
Associated harnessing, hardware, and brackets

2. Hydraulic hoses - Dealer is responsible for fabricating and sourcing hoses.

3. SectionCommand meter cartridges will be needed for each meter. These meter cartridges contain gates, gate detection sensors, and a secondary meter lock-down. See Meter cartridges for field conversion for more information.

4. New Operator’s Manual including SectionCommand. Order A98462 or newer 1910 operator’s manual when installing onto a model year 2013 19,400-L (550-bu) cart or all model year 2014 carts.

Ensure the latest version of software is installed on both cart controller and in-cab display.

All SectionCommand kits are sold in eight-run configurations. If pairing the cart with a tool of seven runs or less, order one - BA32812 meter run reduction kit per cart. This kit contains parts to block off runs not used when pairing a cart with a tool of seven runs or less.

NOTE: For SectionCommand to operate properly, it must be installed on each meter.

SectionCommand™ savings calculator assists operators in determining potential savings

To assist in determining savings potential for an operation when using SectionCommand, please utilize the savings calculator. A link is provided for access to the calculator.

Directions:

The savings calculator can calculate savings potential for up to three crops. Insert the variables into the yellow boxes for each of the three crops. Input variables include:

Crop(s)
Acres of each crop
Seeding rate per acre
Seed price per pound
Fertilizing rate per acre
Fertilizing rate per pound

Green boxes will list the potential savings per crop and total savings are listed at the bottom of the page.

1910 Cart brakes

Cart brakes are an option with 430 Tow Between, 430 Tow Behind, and 550 Tow Behind carts. The brakes are required when using a 18.3-m (60-ft) N560F Disk Drill or 23.2-m (76-ft) P576 Air Hoe Drill.

The air cart hydraulic brakes connect to the tractor’s hydraulics through a brake connection at the rear of the tractor. Tow behind carts require an extension hose for the air seeding tool.

The air cart brake system supplements the tractor brakes. The cart system senses when the tractor’s brakes are applied and engages a caliper on a rotor at each rear axle hub.

Ensure the tractor has a hydraulic brake port and is equipped with adequate ballast for the air cart and seeding tool.

Air Power™ 2 fan drive system

Air Power 2 fan drive system

Enhanced air seeding performance would not be possible without the updates to the 15,152-L (430-bu) and 19,381-L (550-bu) 1910 and C850 air carts.

For the wider seeding width, more fan capacity has been added.

Air Power 2 provides two independently controlled fans – one for seed, one for fertilizer. Along with 76.2-mm (3-in.) primaries, more accurate delivery rates are possible across the full width of the seeding tool – from opener to opener. Air Power 2 delivers high rates, up to 40 percent more product delivery per primary compared to the single-fan system.

Dual fans are required for tow-between and tow-behind carts on the 23.2-m (76-ft) P576 and the 18.3-m (60-ft) N560F. Each fan will direct air to one set of primaries. Two selective control valves (SCVs) are required for the fans. The fan speed will be controlled through the SCV flow control.

Air Power 2 will also be compatible with:

17-m (56-ft) P556
13-m (43-ft) N543F
15.2- and 18.3-m (50- and 60-ft) 1890 models

An option is available for stainless-steel primaries to resist corrosion from high fertilizer rates.

C850 Air Cart

There is a slide at the meter to choose bottom or top shoot for each product. There is also a valve on the tank pressure system to choose top or bottom shoot. This same valve is used to adjust the amount of air to the tank to create the proper pressure differential.

Pressure valve handle

The arrow on the valve handle should be pointing to the top of the range for the top shoot and the bottom of the range for the bottom shoot. If the tank will not be in use, set the pressure valve to the middle setting to not pressurize the tank. The operator should use the gauge to find the correct setting. Location of pressure read-out:

1910 Tow-Behind left-hand side of cart on pressure gauge*
1910 Tow-Between front of the cart on pressure gauge*
C850 Air Cart side display

* The electronic pressure sensor is located behind the mechanical gauge on the side of the cart.

For all Air Power 2 configured carts, an electronic pressure sensor will send a warning to the display if the tank pressure differential is out of range. If pressure is in the green operating range, the tanks are sealed and operating correctly.

Tank warnings on the GreenStar™ 3 2630 Display

NOTE: Only applies to 1910 AirPower 2 Carts as the C850 Cart is only compatible with the Gen 4 4600 CommandCenter™ or 4640 Universal Display.

Tank warning on display

The operator will receive a warning in the display if a tank’s pressure is above or below normal working range. There will be a warning sign over the tank with the out-of-range issue.

Select the icon to view the tank pressure screen.

Tank pressure screen – plus indicates too much product

The operator can press on the red warning and get a screen that looks like the picture above. The plus indicates the pressure is out of range and could be delivering too much product.

Tank pressure screen – minus indicate too little product

The minus indicates the pressure is out of range and could be delivering too little product.

*Only applies to 1910 Air Power 2 Carts as the C850 Cart is only compatible with the Gen 4 4600 CommandCenter™ or 4640 Universal Display.

NOTE: A quick reference guide will ship with every operator’s manual. Please reference that and the operator’s manual for more detailed information.

Camera ready

Monitoring the product levels in tanks has never been easier with the camera-ready feature of the 1910 and C850 Air Carts. The carts come pre-wired to accept a camera in each tank and on the rear of the machine. Cameras allow the operator to conveniently monitor product levels in each tank, which is especially reassuring when product levels are low. Cameras also provide the operator with visibility behind the cart when traveling down the road.

Camera locations on the 1910 Air Cart

Camera location on the C850 Air Cart

For the 1910 Air Carts, the producer has the choice of linking up to three cameras (CabCAM™ or Voyager® cameras) to a GreenStar™ 3 2630 Display or up to four Voyager cameras on a Generation 4 4600 CommandCenter™ Display or 4640 Universal Display. If the producer wants to view more than four cameras, a producer-purchased camera display will be needed.

For C850 Air Carts, the producer can use up to four Voyager cameras on a Generation 4 4600 CommandCenter Display or 4640 Universal Display. If the producer wants to view more than four cameras, a producer-purchased camera display will be needed.

NOTE: Generation 4 displays only support Voyager cameras.

While the 1910 and C850 Air Carts come pre-wired to adapt cameras, additional harnesses are necessary for connecting to the tractor, and a tool overlay harness will be needed for tow-behind carts. Please use the option codes below if ordering on a new machine or the part numbers for configuring an existing machine.

Option code	Description	Parts
9610	Tool overlay harness	AA94564
9615	Gen 4 4600 CommandCenter Display tractor cab harness	AA93727 (order one per camera) AA94316
9620	4640 Universal Display tractor cab harness	SWTY268456 AA94316
9625	GreenStar 3 2630 Display tractor cab harness	AA94319 AA94316

Some carts may require SWVOSCCAM and AA96311, a Voyager connector to CabCAM connector, on the rear of the cart.

CabCAM is a trademark of ATI Products, Inc. Voyager is a trademark of ASA Electronics, LLC.

Specifications

Compare the specifications of up to 4 models

Key Specs	1910-air-commodity-cart Current Model
Sizes - Tow-between model	2-tank 270, 350 bu 9531, 12355 L 3-tank 250, 430 bu 8826, 15179 L
Sizes - Tow-behind model	2-tank 270, 350 bu 9531, 12355 L 3-tank 250, 340, 430, 550 bu 8810, 12002, 15179, 19381 L
Fan size	44.7 (single), 66.04 (dual) cm 17.6 (single), 26 (dual) in.
Fan speed	2000 to 5000 rpm
Meter rolls	Up to 8 individual meter segments
Meter settings	Infinitely variable 0-265 lb per acre
Sizes
Tow-between model	2-tank 270, 350 bu 9531, 12355 L 3-tank 250, 430 bu 8826, 15179 L
Tow-behind model	2-tank 270, 350 bu 9531, 12355 L 3-tank 250, 340, 430, 550 bu 8810, 12002, 15179, 19381 L
Fan
Type	Hydraulic motor, 26.5 USGPM @ 5000 psi max.
Size	44.7 (single), 66.04 (dual) cm 17.6 (single), 26 (dual) in.
Speed	2000 to 5000 rpm
Meter drives
Type	Drive shaft
Variable rate drive	Mechanical
Variable rate control	Electric
Limp home mode	Yes
Tanks
Type	Translucent polyethylene
Lids	Diameter Round: 67.31 cm Diameter Round: 26.5 in.
Open-lid indicators	Standard equipment
Meters
Meter rolls	Up to 8 individual meter segments
Identify	Color-coded meter rollers
Settings	Infinitely variable 0-265 lb per acre
Half-width disconnect	Yes
Fine-tuning rings	Yes
Monitor



Conveyance



Tires
Rear wheels and tires	All-weather turf tread (standard)
Front wheels and tires
Ergonomics
Access	Staircase with railing
Fill lights	Standard
Freight

Accessories and Attachments

Electrical

CAN transition bridge - BA28777

The 7-pin extension harness attaches to the seeding tool. It supplies power to the 1910 Cart meter clutches and monitor system. It also supplies power to the seeding tool warning lights and cart warning lights.

The CAN extension harness is for the SeedStar^TM monitor. It assembles to the seeding tool and connects from the front of the cart to the back of the tractor.

Notes:

May be required for tow-behind carts attached to non-John Deere seeding tools.
Monitor and 7-pin extension harnesses are normally supplied with John Deere seeding tools.
Will not be needed if the air package is ordered with the seeding tool as a code.

Miscellaneous

12 In. Conveyor for 250, 270 and 340 Bu. Cart - BA92750

Kits for conveyance systems

1910 Cart auger

Choose from two options when selecting the conveyance system for the 1910 Commodity Air Cart. Choose between an auger or conveyor. Fill time is less than 15 minutes and unloading time is less than 10 minutes. The lighting system at the hitch alerts the operator as to when the tank product levels are approaching full during a fill.

The auger is available with steel or brush flighting on all sizes, or cupped, to gently handle seed, which is available on the 8-inch auger only. These conveyance systems are recommended for beans and legumes, but not fertilizers.

NOTES:

Hydraulic hose kit may be required. If cart was originally ordered less auger (Option code 4595), then hydraulic hose kit is required. For more information on hydraulic hose kits for conveyance systems, please consult: conveyance hydraulic hose attachments
Conveyance swing arm system may be required. When adding a conveyor to a 1900 Cart OR to a 1910 Cart prior to serial numbers (A01910T700346 Tow-Between or A01910H700409 Tow-Behind), an arm system is required. When adding an auger attachment to a 1900 Cart or 1910 Cart prior to serial numbers (A01910T700346 tow-hetween or A01910H700409 Tow-Behind), an arm system is required due to changes in latching system. Tow-between 1910 Carts above serial number (A01910T700346) and tow-behind carts above serial number (A01910H700409) do not require updates to arm system. Please consult conveyance arm attachments for additional ordering information.
All 7-in. and 8-in. auger attachments require A60206 auger hopper from Service Parts.
7-in. and 8-in. augers do not include downspouts. For a 7-in., flexible downspout, order (1)A61684 tube and (2) TY22495 clamps from Service Parts. For a 8-in. flexible downspout, order (1) A60207 tube and (2) TY22497 clamps from Service Parts. For a telescopic spout for 8-in. augers, please consult telescoping spout attachments for field conversion. 12-in. conveyors have a telescopic spout included in the bundle as standard equipment.

203.2-mm (8-in.) steel flight auger for 250, 270 and 340 bushel cart - BA29967

Auger Arm Kit for 250, 270 and 340 Bu. Cart - BA92791

Swing arm kit

1910 Cart auger

The swing link arm allows for better movement with the redesigned pivot. It has a larger ''sweet spot'' for easier movement and placement of the hopper.

NOTE: Required if cart was previously ordered without an auger/conveyor system (code 4595).

Blockage sensors - 1 per bundle - BA31271

Brackets, wire harness guide - BA31326

Conveyor Arm System - BA92752

Swing arm kit

1910 Cart auger

The swing link arm allows for better movement with the redesigned pivot. It has a larger ''sweet spot'' for easier movement and placement of the hopper.

NOTE: Required if cart was previously ordered without an auger/conveyor system (code 4595).

Dual module bracket, 12 member module, 3 harness - BA31279

Dual module bracket, 16 member module, 4 harness - BA31280

Eight port secondary tower - BA31992

Eleven port secondary tower - BA31995

Flow through hydraulic hose kit - 1895 and tow behind cart - BA31176

TBH cart with tool and tractor

See link below for information on seeding tool and TBH cart compatibility.

1910 Tow-Behind Cart and seeding tool compatibility

See link below for information on hydraulic, electrical, and software requirements for pairing hydraulic drive carts with model year 2013 and older seeding tools.

Hydraulic drive cart requirements for software, hydraulic and electrical overlays

The following table outlines hydraulic hose overlay AFC kits available for:

Power beyond, return, and load sense for hydraulic drive and SectionCommand™
Fan power, return, and case drain

All model year 2014 and newer tools paired with TBH carts are shipped from the factory with overlay hoses for both number’s one and two from above.

Model 2013 and older tools did not have power beyond, return, and load sense hoses installed except for when paired with a 550 bu TBH cart. If pairing a model year 2013 or older tool with a TBH cart, hoses for power beyond, return, and load sense will need installed and can be seen below.

Flow through hydraulic hose kit - All tools except 1895 and tow behind cart - BA31175

TBH cart with tool and tractor

See link below for information on seeding tool and TBH cart compatibility.

1910 Tow-Behind Cart and seeding tool compatibility

See link below for information on hydraulic, electrical, and software requirements for pairing hydraulic drive carts with model year 2013 and older seeding tools.

Hydraulic drive cart requirements for software, hydraulic and electrical overlays

The following table outlines hydraulic hose overlay AFC kits available for:

Power beyond, return, and load sense for hydraulic drive and SectionCommand™
Fan power, return, and case drain

All model year 2014 and newer tools paired with TBH carts are shipped from the factory with overlay hoses for both number’s one and two from above.

Flush face motor case drain coupler for 30-60 Series Row Crop Tractors and 30-50 Series 4-Wheel Drive Tractors - BA30132

Flush face case drain coupler

For installing tractor case drain for vacuum motors. A motor seal drain kit (return to sump) protects the motor and shaft seal by allowing motor housing pressure to return back to hydraulic reservoir free of any back pressure. Handles up to 3 U.S. gallons per minute.

NOTE: All vacuum planters built after 1 May 2004 have hydraulic case drain vacuum motors. These motors have a flush-face case drain hose tip on the return oil line that must be routed to the tractor's sump/case drain port. The tractor requires a case drain coupler be installed in this port to accept the return hose.

This kit is required for operation of 1910 Commodity Air Cart and 1990 CCS^TM hydraulically-driven fan.

Flush face motor case drain coupler for 60-70 Series 4-Wheel Drive Tractors - BA30133

Flush face case drain coupler

This kit is required for operation of 1910 Commodity Air Cart and 1990 CCS^TM hydraulically-driven fan.

Hardware, fold joint - BA31263

Harness, CAN hitch no blockage - Tow behind - BA31272

Harness, primary blockage 16-split - BA31269

Harness, primary blockage 8-split - BA31268

Hitch - Yard for tow-behind 1900 or 1910 Cart - BA32302

Hydraulic hose kit with Power Beyond, return and load sense - 1895 and Tow Behind Cart - BA32686

TBH cart with tool and tractor

See link below for information on seeding tool and TBH cart compatibility.

1910 Tow-Behind Cart and seeding tool compatibility

See link below for information on hydraulic, electrical, and software requirements for pairing hydraulic drive carts with model year 2013 and older seeding tools.

Hydraulic drive cart requirements for software, hydraulic and electrical overlays

The following table outlines hydraulic hose overlay AFC kits available for:

Power beyond, return, and load sense for hydraulic drive and SectionCommand™
Fan power, return, and case drain

All model year 2014 and newer tools paired with TBH carts are shipped from the factory with overlay hoses for both number’s one and two from above.

Hydraulic hose kit with Power Beyond, return and load sense - All tools except 1895 and Tow Behind Cart - BA32685

TBH cart with tool and tractor

See link below for information on seeding tool and TBH cart compatibility.

1910 Tow-Behind Cart and seeding tool compatibility

See link below for information on hydraulic, electrical, and software requirements for pairing hydraulic drive carts with model year 2013 and older seeding tools.

Hydraulic drive cart requirements for software, hydraulic and electrical overlays

The following table outlines hydraulic hose overlay AFC kits available for:

Power beyond, return, and load sense for hydraulic drive and SectionCommand™
Fan power, return, and case drain

All model year 2014 and newer tools paired with TBH carts are shipped from the factory with overlay hoses for both number’s one and two from above.

International Standard Organization (ISO) blockage main components - Tow-behind cart - BA31651

Module and harness bracket, 10 member module, 3 harness - BA31285

Module and harness bracket, 4 member module, 1 harness - BA31282

Module and harness bracket, 5 member module, 2 harness - BA31281

Module and harness bracket, 6 member module, 2 harness - BA31283

Module and harness bracket, 8 member module, 2 harness - BA31284

Nine port secondary tower - BA31993

Non-SectionCommand meter roller - High rate (green) - 13.6078 to 99.7903 kg (30 to 220 lb) per acre - BA29096

There are five types of meter cartridges available to match seed and fertilizer types and rates.

Low rate

Low-rate meter roller

The yellow, low-rate meter roller is for rates from 0.91 up to 9.07 kg/ha (2 up to 20 lb/acre) for seeds such as flax, canola, and alfalfa. The low-rate meter roller rotates more continuously, minimizing pulsing effect for better metering at low rates. There are 20 flutes on this meter roller. Each flute is 8-mm (0.31-in.) wide at the top, 2-mm (0.08-in.) wide at the bottom, and 1.5-mm (0.06-in.) deep.

Medium rate

Medium-rate meter roller

The black medium-rate meter roller is for rates from 9.07 up to 59 kg/ha (20 up to 130 lb/acre) for seeds such as wheat, barley, canola, and small soybeans up to 6.35 mm (0.25 in.) in diameter. It is also used for medium rates of fertilizer. This is the most commonly used meter roller. There are 10 flutes on this roller, which are 18.5-mm (0.73-in.) wide at the top of the flute, 12-mm (0.47-in.) at the bottom of the flute, and 8-mm (0.31-in.) deep.

High rate

High-rate meter roller

The green, high-rate meter roller is for rates from 30 up to 99.8 kg/ha (220 lb/acre), such as high rates of fertilizer and large soybeans bigger than 6.35 mm (0.25 in.) in diameter. There are 10 flutes, which are deeper and wider. Each flute is 21.5-mm (0.85 in.) wide at the top of the flute, 8-mm (0.31-in.) wide at the bottom of the flute, and 14-mm (0.55-in.) deep.

Very high rate

Very high-rate meter roller

This blue roller is for rates from 22.7-120.2 kg/ha (50-265 lb/acre), or seeds such as barley and oats with beards. It is also used for large seeds such as garbanzo beans (in non SectionCommand™ system applications) or very high fertilizer rates. There are six flutes, which are very deep and widely spaced.

Large-seed roller for SectionCommand control system

Large seed meter roller

For use with large seeds only (6 mm [0.25 in.] in diameter or larger)
For use with SectionCommand only
Is not for use with fertilizers or cereal grains
Preserves seed quality of large seeds when used with SectionCommand

The width of the seeding tool and the number of furrow openers determine the number of active primary ports. The commodity cart can be equipped with a 3, 4, 5, 6, 7, or 8-run meter roller. One meter roller is required for each tank on the 1910.

When outfitting a cart with SectionCommand, new SectionCommand meter cartridges with gates and gate detection equipment will be needed. SectionCommand is sold in eight-run only configurations. In order to utilize SectionCommand on carts paired with tools less than eight runs, primary reduction kits are available. See table below for more information.

Primary reduction kit

Open or close product runs – C850 Air Cart

NOTE: The following procedure aligns the air cart meter with the seeding tool.

Part identification:

A. Hose clamp
B. Meter cover
C. Cap, 76.2 mm (3 in.) ID
D. Meter seal

NOTE: When metering high rates through a seeding tool with three to four secondary manifolds, it may be necessary to either add secondary manifolds or slow down to achieve a very high target rate.

Non-SectionCommand meter roller - Low rate (yellow) - 0.907185 to 9.07185 kg (2 to 20 lb) per acre - BA29094

There are five types of meter cartridges available to match seed and fertilizer types and rates.